The Pros and Cons of Using Sliding Closet Doors
A 6 foot sliding glass patio door in Paradise is a great thing to have and many homeowners only realize how lucky they are when they finally moved into a house with a patio or backyard that has a sliding exterior door installed. Not only it looks great by enhancing tenfold the ambient of any room or backyard, but it is also very functional. Sliding patio doors are maybe one of the best types of exterior doors due to ease of getting in and out of the room through it.
Unfortunately this particular sliding door type has an ever recurring problem: it get stuck at times. This is why you need to learn how to fix a sticking patio sliding door. It is not difficult by any means, but you do need to have a bit of DIY knowledge and some basic home tools. The good news is that you can very easily remove the sliding patio doors by simply lifting them up and swinging them out from the aluminum bottom. Then all you need to do is follow the same procedure for the top part as well.
However why do patio sliding doors get stuck in the first place? Many times there is a malfunctioning of the gliding system. Sometimes though there is a corrosion of the hardware or maybe it’s simply tightened up. Depending on the cause, it can be easily fixed and adjusted. For example if it’s tightened, all you need to do is loosen up the screw that keeps the wheel in place. However when you do this make sure you do it gently with your tools because in case the material has become brittle over time, it might simply break when you handle it.
Barn Door Hardware
The most common thing that a sliding door is used is on garages. Sliding garage doors often come with an automatic trigger for convenience. These automatic doors can operate with a flick of a button.
One of the advantages of having them is on a bad weather. You can easily open them without getting out of your car; you don't need to get wet or even call for somebody inside your house to open them for you.
But with this great tool, there are also cons. The battery operated garage doors must be checked occasionally for smooth operation. On rare cases, if there is a relative nearness to other doors, your neighbors' garage door might be activated too.
Also with long time usage, the doors might get stuck sometimes; this is also true to old cars having automatic window problems. It usually gets stuck and the rails don't work correctly as they should. They can be easily opened again with helping them manually.
But with this problem being a common one, they can be repaired easily by professionals or you can contact the manufacturer and you won't spend anything as long as they are still covered by the warranty.
Garage doors that open automatically have some basic features. As with security, they have an auto stop feature so your car won't get scratched during operation or to prevent your kids to get caught. There is usually a panic button to halt the operation to prevent it to forcibly close the door.
As with common sliding doors, there are also lateral sliding doors. They consist of panels which are joined together to run on a track located on its top. It is also guided by the bottom track which can be either being surface mounted or installed within the floor.
Each sliding garage door is supposedly made to fit the client's needs. Both types of doors have manual/remote operation buttons and the option to have electrical operation.
You can easily find replacement rollers or glides at the local DIY hardware store and they are not expensive either, but as there are so many types available nowadays, you need to take your old one with you. Before you get a new one, first try to readjust the wheel and put back the door in its place. Give it a try and see if the problem has been fixed. If not, then that trip to the DIY store will need to be tackled next.
A Look at Sliding Doors
Last week I told you how to remove your old sliding glass door in preparation for the installation of the vinyl replacement door. Let's go through the installation procedure for both the Retrofit style and replacement style frames.
Let's start with the retrofit frame. Like the retrofit window, the door will have a 2" lip flush with the outside edge of the frame. The difference between the retrofit window frame and the retrofit door frame is the absence of the lip on the bottom of the door due to the sill track. Your door will have the lip on both sides and across the top. The majority of the installation process is the same whether it's a retrofit frame or replacement frame. The first thing you want to do is check the floor for a level condition. If the base is not level, add shims to create a level base. This step is very important, because if you have a sloping bottom, the whole frame will be thrown out of square. You will have problems locking the door as well as air infiltration trouble. So, put down shims to make the base level. If possible, use one long shim to create a solid base for the weight of the door. Before setting the door in place, put down a bead of liquid nails from end to end, set the shims on top of the liquid nails, and run a generous bead of caulk on the outside face of the opening, where the retrofit lip is going to contact the exterior surface. Caulk the sides and the top.
Now set the door in place, being careful to lift the door and set the bottom track on top of the shims, rather than dragging the bottom. Obviously, this requires two people, one on each side. You tilt the top away from the opening as you set the bottom in place. Then, raise the top until the retrofit lip contacts the exterior surface where you applied the caulk. The reason I use liquid nails on the bottom rather than caulk is because I don't like to put screws in the bottom, and the liquid nails product is as good as screws when it dries. Have your helper hold the frame in place while you go inside to plumb and secure the door. Put a level on the jamb where the slider will lock. Plumb the jamb and install shims where you put your screws. You should put one about 6 inches from the top and one 6 inches from the bottom. A good quality door will have long screws shipped with the door that are replacements for the small screws holding the locking hardware to the jamb. Be sure to shim where these screws install. Now, if you leveled the bottom and plumbed the side, your top and opposite side should automatically be square. Put shims on the opposite jamb, and drive in your installation screws. Put 3 to 4 screws in the jamb. Then, run your tape measure from the top right corner to the bottom left corner. Write down that measurement. Measure from the opposite corners, and the measurement should be the same if your frame is square. Finally, put one screw in the top center You really don't need any more than one. You don't need to use shims since there won't be any load or torque on the top header. Just don't overtighten the screw, otherwise the frame will bow.
At this point you should have the frame installed in the opening with the fixed panel already glazed in from the factory. Here is where you want to install the sliding panel. It goes in from inside the house. Set it on the side and spray a generous amount of lubricant to the steel rollers to help them spin freely. Wipe away excess before putting the panel in. Remember to raise the top into the header as far as it will go, then swing the bottom over the lip and set it down on the track. If the bottom won't get over the bottom lip, you will have to adjust the bottom rollers to bring them up into the frame. You should see a hole on the side rail to insert a screwdriver and turn the adjustment screw counterclockwise to bring the rollers up and out of the way. After you set the rollers on the track, be sure to adjust them back down before sliding the door. Have your helper lift the side up while you turn the adjustment screw clockwise. Do both sides, then slide the door closed and check for equal daylight from top to bottom. If there is more daylight showing on top or bottom, adjust the rollers to bring the door panel plumb with the jamb. Adjust the lock. Each door should come with lock adjustment instructions. Install the screen door on the outside. Now seal the crack between the retrofit lip and the exterior surface. Go inside and fill the space between the frame and wall studs with R-13 insulation. The last step is trimming the inside. We sell vinyl trim pieces that are designed to trim the inside without having to paint, stain, or nail. You can see samples and prices for the trim at the shopping pageon the website.
Now, the replacement frame installation process is the same, except there is no retrofit lip. Therefore, when you put the frame into the opening, you have to plumb the side jambs from two places rather than one. In addition to plumbing the jamb left to right in the opening, you also have to plumb inside to outside because you don't have the retrofit lip to keep your frame aligned with the outside wall. Also, you need to apply trim to the exterior as well as the interior. You can use a basic vinyl flat trim for the outside, and that is available on the shopping page as well. Be sure to caulk the outside trim where it meets the surrounding surface.You just installed a vinyl sliding glass door. I will be on vacation next week, but the following week's article will deal with the best and safest way to install replacement windows on the second floor.
Many times the gliders or rollers are simply full of dirt. Again, you can replace them, but first try to clean them as this might save you a buck or two. All you need to use is an old toothbrush (I collect my old toothbrushes just for emergency cleaning situations like this) and some spirit (or kerosene) to clean off the dirt from your rollers. As there is a danger of inhaling these fumes you should always work in a well ventilated place and make sure to use some rubber gloves. After you have cleaned, them lubricate them with any kind of grease you have around and try the sliding patio glass door again. It might just work this time.
Installing Vinyl Replacement Sliding Glass Doors
Sliding barn door hardware, along with the barn doors, doesn't have to be for barns anymore. Today, barn doors on domestic living spaces are becoming extremely popular due to the aesthetic design and their space saving features. Instead of needing extra space to open a traditional door, barn doors can slide back and forth, eliminating the need for a large space.
Barn doors for indoor purposes can also create a very unique rustic look that can enhance the ambience of any room. There are several types of barn doors and hardware that can work with the design you want to create, including modern and industrial hardware. When considering barn doors for your next project, consider the following hardware and doors, as well as their purposes, so you can get the right products. All hardware packages come with mounting instructions, so you can get it right the first time.
Modern Sliding Door Hardware
What's Your Next Project?
While we know that sliding barn doors are not for everyone, we do realize that sliding doors can be useful in almost any application. With our quiet rollers, you can create a very nice entrance into a nursery or any bedroom, as well as in spaces where events are held. Or with our industrial sliding barn door hardware, you can create an industrial look that is becoming more popular in urban lofts. Any domestic residence or public space can benefit from our sliding barn door hardware. What's your next project?
A Look at Sliding Doors
You cannot appreciate just how practical sliding closet doors are until you install them to hide your wardrobe in your bedroom. These user-friendly doors slide on tracks, look fabulous and can certainly tidy up the appearance of your room. However, buying the cheap choice is not always a good idea because what may be acceptable for one person may not be practical for you. Although you may find some discounted, make sure that they are still of good quality.
The advantages of these systems far more than outweigh any minor disadvantages. The number one reason people choose to buy these designs is the floor space that they open up for you. As you are probably well aware, the less crammed you feel, the more comfortable you ultimately are. Since you aren't having to open a conventional door that is held in place with hinges, you no longer have to worry about positioning your bed a little further away so you don't hit it with the door every time you need something out of your closet.
Not only do wardrobe sliding doors save you an abundance of space, they are much more contemporary looking as well. Big brass doorknobs that you hang everything on are part of the past. Today, the look is clean, streamlined, modern and even mirrored. Not to mention, these types of closet doors allow you to access every inch of your closet. Now you don't have that dead corner where you store certain items and then end up forgetting about them because they are out of sight. The fact that you can slide the doors on the track either way allows you to make the most of your wardrobe space.
The disadvantages associated with these doors are mild and also easy overcome. A traditional sliding door does not allow you access to your whole closet at one time. Even when the doors are open fully, one part of the space is blocked unless you slide the doors to the other side.
This is actually easily remedied one of two ways. You can create a pocket inside an adjacent wall where the doors can simply slide into and disappear or you can opt for the accordion style. These designs fold in half on the track to slide open away from each other. These are probably one of the most popular types of sliding closet doors available today but be cautious when making your purchasing decision because a lot of them can be really poor quality. You'll find that these systems come in a variety of materials, colors and mirrored or even louvered patterns.