The Pros and Cons of Using Sliding Closet Doors
A sliding door company in Madison is a great thing to have and many homeowners only realize how lucky they are when they finally moved into a house with a patio or backyard that has a sliding exterior door installed. Not only it looks great by enhancing tenfold the ambient of any room or backyard, but it is also very functional. Sliding patio doors are maybe one of the best types of exterior doors due to ease of getting in and out of the room through it.
Unfortunately this particular sliding door type has an ever recurring problem: it get stuck at times. This is why you need to learn how to fix a sticking patio sliding door. It is not difficult by any means, but you do need to have a bit of DIY knowledge and some basic home tools. The good news is that you can very easily remove the sliding patio doors by simply lifting them up and swinging them out from the aluminum bottom. Then all you need to do is follow the same procedure for the top part as well.
However why do patio sliding doors get stuck in the first place? Many times there is a malfunctioning of the gliding system. Sometimes though there is a corrosion of the hardware or maybe it’s simply tightened up. Depending on the cause, it can be easily fixed and adjusted. For example if it’s tightened, all you need to do is loosen up the screw that keeps the wheel in place. However when you do this make sure you do it gently with your tools because in case the material has become brittle over time, it might simply break when you handle it.
Garage Doors - Upgrade Your Carport With Sliding Doors
The new home improvement fad that is becoming very popular is what is known as bard door hardware. These are large sliding barn doors that are to be used inside your home and slide open for any room in your house.
They are a little pricey but they add a lot of style to any room. The hardware itself is very expensive and consists of metal wheels, a metal track and the necessary bolts to mount it to the wall. It seems as though it wouldn't cost very much for such a simple sliding track but be prepared to spend somewhere around $400 dollars for the lower end and around $800 for the upper end quality. This will not include the price of the actual door or doors. You will have to find them somewhere locally and you can have them hand crafted to fit your own personal style.
This is a new fashion trend for the home so get in on it before all of your friends already have one. They also have sliding mirrors online that you can use in a bathroom to slide over a window when you want privacy. The concept is great because you don't have to plan out extra living space for the area that a normal door would occupy when opening. These do not slide inside of the wall like some of the sliding doors you might have seen. The door remains visible on one side of the wall when it is opened or closed.
You can easily find replacement rollers or glides at the local DIY hardware store and they are not expensive either, but as there are so many types available nowadays, you need to take your old one with you. Before you get a new one, first try to readjust the wheel and put back the door in its place. Give it a try and see if the problem has been fixed. If not, then that trip to the DIY store will need to be tackled next.
Barn Doors, Not Just for Barns Anymore
Barn door hardware is quickly gaining popularity. But why? Here we'll briefly touch on a few reasons.
Barn door hardware, also known as sliding door hardware or flat track hardware, has become a popular new alternative to pocket doors. There are several reasons for this, but here are just a few.
1) Solid Construction
Sliding hardware, given its traditional application as barn door hardware, is made of solid steel. The standard track is 2" wide by 1/4" thick, making it strong and durable. Standard track systems can bear doors that weigh up to 400lbs! Additionally, the bearings in the wheels of the door hangers are guaranteed lubricated for life. Essentially, these sliding door hardware systems are built to outlast the life of your home.
2) Sliding doors = exciting! Pocket doors = outdated!
Another finish that is popular is the Acrylic Clear Coat finish. The entire system, including the track and hangers, is coated in an acrylic clear coat that seals and protects the steel, while at the same time preserving the rustic nature of a raw mill steel look. This finish is just right for any door that has a slightly aged look to it. Dining rooms, bedrooms, and kitchens are popular destinations for hardware with this finish.
Barn door hardware is a unique trend that is growing fast. With as an exciting alternative to pocket doors with its solid construction and unique finishes, it is no wonder why homeowners and designers alike are turning to sliding door hardware for their doorway needs.
Many times the gliders or rollers are simply full of dirt. Again, you can replace them, but first try to clean them as this might save you a buck or two. All you need to use is an old toothbrush (I collect my old toothbrushes just for emergency cleaning situations like this) and some spirit (or kerosene) to clean off the dirt from your rollers. As there is a danger of inhaling these fumes you should always work in a well ventilated place and make sure to use some rubber gloves. After you have cleaned, them lubricate them with any kind of grease you have around and try the sliding patio glass door again. It might just work this time.
Sliding Patio Door Repair - How to Fix a Sticking Patio Door
Last week I told you how to remove your old sliding glass door in preparation for the installation of the vinyl replacement door. Let's go through the installation procedure for both the Retrofit style and replacement style frames.
Let's start with the retrofit frame. Like the retrofit window, the door will have a 2" lip flush with the outside edge of the frame. The difference between the retrofit window frame and the retrofit door frame is the absence of the lip on the bottom of the door due to the sill track. Your door will have the lip on both sides and across the top. The majority of the installation process is the same whether it's a retrofit frame or replacement frame. The first thing you want to do is check the floor for a level condition. If the base is not level, add shims to create a level base. This step is very important, because if you have a sloping bottom, the whole frame will be thrown out of square. You will have problems locking the door as well as air infiltration trouble. So, put down shims to make the base level. If possible, use one long shim to create a solid base for the weight of the door. Before setting the door in place, put down a bead of liquid nails from end to end, set the shims on top of the liquid nails, and run a generous bead of caulk on the outside face of the opening, where the retrofit lip is going to contact the exterior surface. Caulk the sides and the top.
Now set the door in place, being careful to lift the door and set the bottom track on top of the shims, rather than dragging the bottom. Obviously, this requires two people, one on each side. You tilt the top away from the opening as you set the bottom in place. Then, raise the top until the retrofit lip contacts the exterior surface where you applied the caulk. The reason I use liquid nails on the bottom rather than caulk is because I don't like to put screws in the bottom, and the liquid nails product is as good as screws when it dries. Have your helper hold the frame in place while you go inside to plumb and secure the door. Put a level on the jamb where the slider will lock. Plumb the jamb and install shims where you put your screws. You should put one about 6 inches from the top and one 6 inches from the bottom. A good quality door will have long screws shipped with the door that are replacements for the small screws holding the locking hardware to the jamb. Be sure to shim where these screws install. Now, if you leveled the bottom and plumbed the side, your top and opposite side should automatically be square. Put shims on the opposite jamb, and drive in your installation screws. Put 3 to 4 screws in the jamb. Then, run your tape measure from the top right corner to the bottom left corner. Write down that measurement. Measure from the opposite corners, and the measurement should be the same if your frame is square. Finally, put one screw in the top center You really don't need any more than one. You don't need to use shims since there won't be any load or torque on the top header. Just don't overtighten the screw, otherwise the frame will bow.
At this point you should have the frame installed in the opening with the fixed panel already glazed in from the factory. Here is where you want to install the sliding panel. It goes in from inside the house. Set it on the side and spray a generous amount of lubricant to the steel rollers to help them spin freely. Wipe away excess before putting the panel in. Remember to raise the top into the header as far as it will go, then swing the bottom over the lip and set it down on the track. If the bottom won't get over the bottom lip, you will have to adjust the bottom rollers to bring them up into the frame. You should see a hole on the side rail to insert a screwdriver and turn the adjustment screw counterclockwise to bring the rollers up and out of the way. After you set the rollers on the track, be sure to adjust them back down before sliding the door. Have your helper lift the side up while you turn the adjustment screw clockwise. Do both sides, then slide the door closed and check for equal daylight from top to bottom. If there is more daylight showing on top or bottom, adjust the rollers to bring the door panel plumb with the jamb. Adjust the lock. Each door should come with lock adjustment instructions. Install the screen door on the outside. Now seal the crack between the retrofit lip and the exterior surface. Go inside and fill the space between the frame and wall studs with R-13 insulation. The last step is trimming the inside. We sell vinyl trim pieces that are designed to trim the inside without having to paint, stain, or nail. You can see samples and prices for the trim at the shopping pageon the website.
Now, the replacement frame installation process is the same, except there is no retrofit lip. Therefore, when you put the frame into the opening, you have to plumb the side jambs from two places rather than one. In addition to plumbing the jamb left to right in the opening, you also have to plumb inside to outside because you don't have the retrofit lip to keep your frame aligned with the outside wall. Also, you need to apply trim to the exterior as well as the interior. You can use a basic vinyl flat trim for the outside, and that is available on the shopping page as well. Be sure to caulk the outside trim where it meets the surrounding surface.You just installed a vinyl sliding glass door. I will be on vacation next week, but the following week's article will deal with the best and safest way to install replacement windows on the second floor.
Garage Doors - Upgrade Your Carport With Sliding Doors
Refurbishing or planning a project to build barn doors? Are you on a look out for resources or strategies for conversion of your barn? Sliding door hardware is the same as barn door hardware, only has dissimilar names. Barn door hardware has turned out to be more well liked term lately given the times gone by and customary use of this hardware. The rural look and concrete steel structure of the hardware in olden days was at times, used for bigger doors on barns. It is very suitable to slither the bigger doors away as an alternative to include them on pivots that might swing out.
There are mainly two types of hardware. One of them is a rural, plain trail sliding door system. The other type is an extra contemporary breaker and trial style system. The rural, plain trail sliding system is ideal for outside door hardware purposes, whereas the contemporary roller and trail style structure is chosen for inner door purposes.
Whether it be an inner or an outdoor barn door sliding hardware, they are extremely fashionable with individuals who desire about having a tidy an exclusive appearance for their barns. It is fair enough because they add an exclusive look to the structural design in general of a specific building. There are several matters using which a sliding door can be assembled. However, it is sensible to purchase weighty and sturdy materials once it comes to barn door sliding hardware. Also, ensure that the matter you select is long-lasting and can tolerate the climate changes. Few advantages of sliding doors have been mentioned below:
Benefits of Barn door sliding hardware
In contrast to swinging doors, sliding doors are more beneficial while it comes to stallion barns constructed for stallions and other mammals or all-purpose ranch storage. Sliding doors are additionally viable and forceful than swinging doors. Sliding doors make managing farm animals a lot easier. The door can be to some extent kept open for the purpose of aeration ensuring that none of the animals manages to break away from that space. Whereas, in case of swinging doors, the animals manage to push the door and break away.
You could also try using a variety of sliding barn door hardware for improved management of farm animals. You should go for a sole big sliding barn door or also try doors of Dutch fashion that can maintain the upper entrance unlocked for aeration and feeding, and keep the lower door closed to lock the mammals within the barn. If you want to select a huge lone sliding door, you can assemble a window in the entrance so that you can peep inside the barn from time to time. If not, the undersized flat swinging door can be kept on top of the sliding door for airing and illumination. There are several designs, which you can select as per your requirement to erect sliding barn doors.
Few steps to follow to erect the ideal and well-completed sliding hardware for your barns:
# Buying the materials and instruments: First, you have to purchase material and instruments such as panels, boards, saw, screws, metal support, power drivers, mallet, and nails
# Take dimensions: You must take the dimensions of the door frame that you want to erect. Also, remember to think about its design while noting the dimensions.
# Cut the planks: Here, you should cut the planks for the frame according to the dimensions taken. Depending on the load and power of the sliding barn door needed twofold or numerous piled timber beams could be used.
# Assemble the border: For assembling the door you might require galvanized screws, metal support, and spikes.
# Planking the entrance: Cut the boards with the aid of an adage as per the height of the entrance and position it on the entrance frame correctly. Fix the boards to the border with bolt, spikes, bonding agent, and wood adhesive.
# Mount the Trail and Helms: Installing the trail is a significant task as it makes the barn door sliding. With the assistance of a carpenter, you have to install the trail above the frame. At the same time, you must install the helm at the base of the door.
# Mount Wall Trails: This is the last step of mounting sliding barn door. As per the dimensions of the border, mount the similar length trails on the barn barrier where the barn barriers retract.
These few major steps assist you while installing barn door sliding hardware with no difficulty. You can color the entrance fashionably as per your liking to improve the attractiveness of the same. You might also write your name at the entrance to give it uniqueness. So, do not hesitate, just proceed and erect the best hardware to make it look the best!