Huntingtoneight foot sliding glass patio door Huntington

The Pros and Cons of Using Sliding Closet Doors

A eight foot sliding glass patio door in Huntington is a great thing to have and many homeowners only realize how lucky they are when they finally moved into a house with a patio or backyard that has a sliding exterior door installed. Not only it looks great by enhancing tenfold the ambient of any room or backyard, but it is also very functional. Sliding patio doors are maybe one of the best types of exterior doors due to ease of getting in and out of the room through it.

sliding glass door installation

Unfortunately this particular sliding door type has an ever recurring problem: it get stuck at times. This is why you need to learn how to fix a sticking patio sliding door. It is not difficult by any means, but you do need to have a bit of DIY knowledge and some basic home tools. The good news is that you can very easily remove the sliding patio doors by simply lifting them up and swinging them out from the aluminum bottom. Then all you need to do is follow the same procedure for the top part as well.

However why do patio sliding doors get stuck in the first place? Many times there is a malfunctioning of the gliding system. Sometimes though there is a corrosion of the hardware or maybe it’s simply tightened up. Depending on the cause, it can be easily fixed and adjusted. For example if it’s tightened, all you need to do is loosen up the screw that keeps the wheel in place. However when you do this make sure you do it gently with your tools because in case the material has become brittle over time, it might simply break when you handle it.

Closet Doors Dare To Be Different

sliding glass door installation

A sliding patio door is a great thing to have and many homeowners only realize how lucky they are when they finally moved into a house with a patio or backyard that has a sliding exterior door installed. Not only it looks great by enhancing tenfold the ambient of any room or backyard, but it is also very functional. Sliding patio doors are maybe one of the best types of exterior doors due to ease of getting in and out of the room through it.

Unfortunately this particular door type has an ever recurring problem: it get stuck at times. This is why you need to learn how to fix a sticking patio door. It is not difficult by any means, but you do need to have a bit of DIY knowledge and some basic home tools. The good news is that you can very easily remove the sliding patio doors by simply lifting them up and swinging them out from the aluminum bottom. Then all you need to do is follow the same procedure for the top part as well.

However why do patio sliding doors get stuck in the first place? Many times there is a malfunctioning of the gliding system. Sometimes though there is a corrosion of the hardware or maybe it's simply tightened up. Depending on the cause, it can be easily fixed and adjusted. For example if it's tightened, all you need to do is loosen up the screw that keeps the wheel in place. However when you do this make sure you do it gently with your tools because in case the material has become brittle over time, it might simply break when you handle it.

You can easily find replacement rollers or glides at the local DIY hardware store and they are not expensive either, but as there are so many types available nowadays, you need to take your old one with you. Before you get a new one, first try to readjust the wheel and put back the door in its place. Give it a try and see if the problem has been fixed. If not, then that trip to the DIY store will need to be tackled next.

Many times the gliders or rollers are simply full of dirt. Again, you can replace them, but first try to clean them as this might save you a buck or two. All you need to use is an old toothbrush (I collect my old toothbrushes just for emergency cleaning situations like this) and some spirit (or kerosene) to clean off the dirt from your rollers. As there is a danger of inhaling these fumes you should always work in a well ventilated place and make sure to use some rubber gloves. After you have cleaned, them lubricate them with any kind of grease you have around and try the sliding patio glass door again. It might just work this time.

You can easily find replacement rollers or glides at the local DIY hardware store and they are not expensive either, but as there are so many types available nowadays, you need to take your old one with you. Before you get a new one, first try to readjust the wheel and put back the door in its place. Give it a try and see if the problem has been fixed. If not, then that trip to the DIY store will need to be tackled next.

Avoid Vinyl When Choosing A Patio Door

interior sliding door options

Many of people have sliding doors that open up to patios or backyards. These doors are an important part of our homes. They have aluminum tracks that let the door slide open and close. Over time, the aluminum tracks breakdown and the sliding door get stuck. The tracks are made from aluminum, which can become pitted and breakdown over time. Aluminum is a softer metal that it widely used because it is light weight, less expensive and adaptable. The manufacturer's coat the aluminum tracks to protect them from corrosion and wear. However, over time the coating is worn off from continually opening and closing,which exposes the track to pitting and breakdown.

Slider doors are frequently used, especially in summer month. With traffic going in and out of the house your sliding door can accumulate small stones, dirt and debris can get trapped in track and cause it to wear down over time. Moisture from weather conditions, such as snow, dew and rain can accumulate in the track and cause corrosion. Once these things happen the doors do not slide as easily and opening and closing making it a challenge.

7. Lubricate the new track for smooth opening and closing

8. Remove the old rollers by removing the frame lock screw, lift frame and then remove. Now slide the new rollers into place and re-install frame lock screw.

9. Re-install the sliding door and test the opening and closing.

As an additional note, it might be worth it to consider purchasing a manual retractable sliding door screen or motorized screen. This screen will allow you to keep your sliding door open in summer, but keep the bugs and insects out. These screens will retract back into their housing when not in use, but will cut down on the opening and closing of your sliding door.

Many times the gliders or rollers are simply full of dirt. Again, you can replace them, but first try to clean them as this might save you a buck or two. All you need to use is an old toothbrush (I collect my old toothbrushes just for emergency cleaning situations like this) and some spirit (or kerosene) to clean off the dirt from your rollers. As there is a danger of inhaling these fumes you should always work in a well ventilated place and make sure to use some rubber gloves. After you have cleaned, them lubricate them with any kind of grease you have around and try the sliding patio glass door again. It might just work this time.

Closet Doors Dare To Be Different

6 ft sliding glass door

Last week I told you how to remove your old sliding glass door in preparation for the installation of the vinyl replacement door. Let's go through the installation procedure for both the Retrofit style and replacement style frames.

Let's start with the retrofit frame. Like the retrofit window, the door will have a 2" lip flush with the outside edge of the frame. The difference between the retrofit window frame and the retrofit door frame is the absence of the lip on the bottom of the door due to the sill track. Your door will have the lip on both sides and across the top. The majority of the installation process is the same whether it's a retrofit frame or replacement frame. The first thing you want to do is check the floor for a level condition. If the base is not level, add shims to create a level base. This step is very important, because if you have a sloping bottom, the whole frame will be thrown out of square. You will have problems locking the door as well as air infiltration trouble. So, put down shims to make the base level. If possible, use one long shim to create a solid base for the weight of the door. Before setting the door in place, put down a bead of liquid nails from end to end, set the shims on top of the liquid nails, and run a generous bead of caulk on the outside face of the opening, where the retrofit lip is going to contact the exterior surface. Caulk the sides and the top.

Now set the door in place, being careful to lift the door and set the bottom track on top of the shims, rather than dragging the bottom. Obviously, this requires two people, one on each side. You tilt the top away from the opening as you set the bottom in place. Then, raise the top until the retrofit lip contacts the exterior surface where you applied the caulk. The reason I use liquid nails on the bottom rather than caulk is because I don't like to put screws in the bottom, and the liquid nails product is as good as screws when it dries. Have your helper hold the frame in place while you go inside to plumb and secure the door. Put a level on the jamb where the slider will lock. Plumb the jamb and install shims where you put your screws. You should put one about 6 inches from the top and one 6 inches from the bottom. A good quality door will have long screws shipped with the door that are replacements for the small screws holding the locking hardware to the jamb. Be sure to shim where these screws install. Now, if you leveled the bottom and plumbed the side, your top and opposite side should automatically be square. Put shims on the opposite jamb, and drive in your installation screws. Put 3 to 4 screws in the jamb. Then, run your tape measure from the top right corner to the bottom left corner. Write down that measurement. Measure from the opposite corners, and the measurement should be the same if your frame is square. Finally, put one screw in the top center You really don't need any more than one. You don't need to use shims since there won't be any load or torque on the top header. Just don't overtighten the screw, otherwise the frame will bow.

At this point you should have the frame installed in the opening with the fixed panel already glazed in from the factory. Here is where you want to install the sliding panel. It goes in from inside the house. Set it on the side and spray a generous amount of lubricant to the steel rollers to help them spin freely. Wipe away excess before putting the panel in. Remember to raise the top into the header as far as it will go, then swing the bottom over the lip and set it down on the track. If the bottom won't get over the bottom lip, you will have to adjust the bottom rollers to bring them up into the frame. You should see a hole on the side rail to insert a screwdriver and turn the adjustment screw counterclockwise to bring the rollers up and out of the way. After you set the rollers on the track, be sure to adjust them back down before sliding the door. Have your helper lift the side up while you turn the adjustment screw clockwise. Do both sides, then slide the door closed and check for equal daylight from top to bottom. If there is more daylight showing on top or bottom, adjust the rollers to bring the door panel plumb with the jamb. Adjust the lock. Each door should come with lock adjustment instructions. Install the screen door on the outside. Now seal the crack between the retrofit lip and the exterior surface. Go inside and fill the space between the frame and wall studs with R-13 insulation. The last step is trimming the inside. We sell vinyl trim pieces that are designed to trim the inside without having to paint, stain, or nail. You can see samples and prices for the trim at the shopping pageon the website.

Now, the replacement frame installation process is the same, except there is no retrofit lip. Therefore, when you put the frame into the opening, you have to plumb the side jambs from two places rather than one. In addition to plumbing the jamb left to right in the opening, you also have to plumb inside to outside because you don't have the retrofit lip to keep your frame aligned with the outside wall. Also, you need to apply trim to the exterior as well as the interior. You can use a basic vinyl flat trim for the outside, and that is available on the shopping page as well. Be sure to caulk the outside trim where it meets the surrounding surface.You just installed a vinyl sliding glass door. I will be on vacation next week, but the following week's article will deal with the best and safest way to install replacement windows on the second floor.


Barn Doors, Not Just for Barns Anymore

A sliding patio door is a great thing to have and many homeowners only realize how lucky they are when they finally moved into a house with a patio or backyard that has a sliding exterior door installed. Not only it looks great by enhancing tenfold the ambient of any room or backyard, but it is also very functional. Sliding patio doors are maybe one of the best types of exterior doors due to ease of getting in and out of the room through it.

Unfortunately this particular door type has an ever recurring problem: it get stuck at times. This is why you need to learn how to fix a sticking patio door. It is not difficult by any means, but you do need to have a bit of DIY knowledge and some basic home tools. The good news is that you can very easily remove the sliding patio doors by simply lifting them up and swinging them out from the aluminum bottom. Then all you need to do is follow the same procedure for the top part as well.

However why do patio sliding doors get stuck in the first place? Many times there is a malfunctioning of the gliding system. Sometimes though there is a corrosion of the hardware or maybe it's simply tightened up. Depending on the cause, it can be easily fixed and adjusted. For example if it's tightened, all you need to do is loosen up the screw that keeps the wheel in place. However when you do this make sure you do it gently with your tools because in case the material has become brittle over time, it might simply break when you handle it.

You can easily find replacement rollers or glides at the local DIY hardware store and they are not expensive either, but as there are so many types available nowadays, you need to take your old one with you. Before you get a new one, first try to readjust the wheel and put back the door in its place. Give it a try and see if the problem has been fixed. If not, then that trip to the DIY store will need to be tackled next.

Many times the gliders or rollers are simply full of dirt. Again, you can replace them, but first try to clean them as this might save you a buck or two. All you need to use is an old toothbrush (I collect my old toothbrushes just for emergency cleaning situations like this) and some spirit (or kerosene) to clean off the dirt from your rollers. As there is a danger of inhaling these fumes you should always work in a well ventilated place and make sure to use some rubber gloves. After you have cleaned, them lubricate them with any kind of grease you have around and try the sliding patio glass door again. It might just work this time.

interior sliding door options

____________________________________________

Home Improvement in sliding door styles  list 

https://homeimprovementcaddy.com/bull-shoals/